Protective-glove RFQs still often say “EN 420 certified,” “CE EN 420,” or “ISO 21420” and stop there. That shorthand is too thin. EN ISO 21420 is the current general requirements and test methods standard for protective gloves. It is not a chemical, mechanical, or thermal performance rating on its own, and it is not a medical-glove pathway.
The International Organization for Standardization’s public abstract for ISO 21420:2020 says the document specifies general requirements and test procedures for glove design and construction, innocuousness, comfort and efficiency, and the marking and information supplied by the manufacturer, applicable to all protective gloves. It also says the document does not address the protective properties of gloves and is therefore not used alone, but only in combination with the appropriate specific standard(s).
This guide restates that public scope at buyer level, using ISO’s abstract and SATRA’s public overview of EN ISO 21420:2020+A1:2024, and lists the questions that belong in an RFQ.
It does not claim that any JUNDA, Yue Long, Baijiebang, or other JUNDA protective or disposable line is EN ISO 21420 assessed, EN 420 certified, or EU type-examined. It is not legal, regulatory, or occupational-safety advice. Confirm requirements against the current standard text, the user information supplied with the glove, destination PPE or medical rules, and the files that belong to the exact SKU to be offered or shipped.
What EN ISO 21420 is — and what it is not
ISO 21420:2020 is titled Protective gloves — General requirements and test methods. ISO’s public record lists publication in February 2020, confirmation in 2025, and Amendment 1 (ISO 21420:2020/Amd 1:2022). The European adoption is commonly written as EN ISO 21420. SATRA’s public article discusses the current EN text as EN ISO 21420:2020+A1:2024.
According to SATRA, EN ISO 21420 replaced EN 420:2003+A1:2009, and the ISO adoption made the general-requirements document a worldwide standard. SATRA states that the scope includes protective gloves, arm protectors, gloves permanently incorporated in containment enclosures, mittens, and pot holders.
What EN ISO 21420 is not:
- It is not a chemical-protection rating. Chemical risks still need a specific pathway such as EN ISO 374.
- It is not a medical-glove barrier standard. Single-use medical gloves are a separate conversation: see EN 455 medical gloves.
- It is not, by itself, a CE mark, a type-examination certificate, or a licence to invent a certificate number from a catalogue.
- It is not a substitute for naming the intended risk: chemicals, mechanical hazards, heat, microorganisms, or another defined workplace risk.
- It is not automatically the right heading for a U.S. medical examination glove, which follows a different device pathway; see FDA 510(k) medical gloves.
Why “EN 420” on an RFQ is now a warning sign
EN 420 was the older European general-requirements standard for protective gloves. SATRA states that EN ISO 21420 replaced EN 420:2003+A1:2009. An RFQ that still says only “EN 420 certified” is usually out of date, and it still fails to name the specific protection standard that 21420 cannot replace.
Ask the buyer—or rewrite the RFQ—to say:
- the intended risk and job;
- EN ISO 21420 (or the current general-requirements text the destination actually uses);
- the specific protection standard(s) that belong with that risk;
- whether the offer is PPE, medical, or another regulatory frame.
Do not treat a leftover “EN 420” line as proof that a current shipment has been assessed to the latest general requirements.
What the general requirements usually cover
SATRA summarises the key requirement groups as glove design and construction, chemical innocuousness, comfort and efficiency (sizing and dexterity), and information supplied by the manufacturer. The following points are SATRA’s public overview, not a substitute for the paid standard text.
Design and construction. Protective gloves should not impair performance of the activity while still providing adequate protection from the risk. For reusable multi-layer gloves, SATRA notes that layers must not become separated during donning and doffing, and that seams must not compromise overall performance.
Innocuousness. SATRA describes this as ensuring that gloves do not adversely affect the health or hygiene of the wearer under foreseeable conditions of normal use. Its public “clause 4.2” box lists example limits that laboratories and notified bodies commonly discuss:
- pH of materials greater than 3.5 and less than 9.5;
- chromium VI in leather less than 3 mg/kg;
- nickel release from metallic parts in prolonged skin contact less than 0.5 µg/cm²/week;
- restricted azo-derived aromatic amines in dyed leather and textiles less than 30 mg/kg each;
- DMFa in polyurethane-containing gloves less than 1,000 mg/kg;
- restricted PAHs in rubbers and plastics in direct skin contact less than 1 mg/kg each.
Those figures belong to SATRA’s overview of the current EN text. Confirm them against the current standard and the materials actually used in the SKU. A nitrile disposable glove, a flock-lined latex protective glove, and a leather industrial glove do not raise the same material questions.
SATRA also notes that notified or approved bodies may ask for evidence against REACH restrictions, and specifically mentions phthalate limits that are especially relevant to vinyl, PVC, or polyurethane materials. That is a documentation question, not a slogan.
Sizing and dexterity. SATRA states that the standard’s size range covers size 4 to size 13, using hand circumference and hand length, and that a different sizing system may be used if it is explained in the user information. Dexterity is graded by the smallest steel pin that can be picked up from a flat surface three times in 30 seconds; if no pin can be picked up, the level is zero. Optional comfort claims, such as water-vapour transmission or absorption, are separate and should only be asked for when they are actually claimed.
Marking and user information. General requirements include what is marked on the glove or packaging and what information the manufacturer supplies. A missing or generic user sheet is a buying defect, not a minor paperwork gap.
SATRA also discusses electrostatic-property claims (tested to EN 16350 when claimed) and environmental annex language. Treat those as optional claimed properties, not as a default for every protective glove.
Why 21420 must sit next to a specific protection standard
ISO’s abstract is unambiguous: the document does not address protective properties and is not used alone. SATRA makes the same point and gives examples of specific standards that evaluate mechanical, thermal, or chemical protection.
For chemical work, that usually means an EN ISO 374 conversation: permeation, penetration, degradation, and type A/B/C language. Breakthrough time remains a laboratory comparison, not a workplace timer.
For other risks, name the standard that actually belongs to the job. Do not assume that a general-requirements test report answers a solvent, cut, heat, or cold question.
SATRA also states that all protective gloves in all PPE categories must fulfil EN ISO 21420, and that notified bodies will require EN ISO 21420 test reports for Category II and Category III protective gloves. SATRA further states that in June 2026 the standard was harmonised, so new EU type-examination applications for protective gloves must be assessed against EN ISO 21420:2020+A1:2024. Attribute that timing to SATRA’s public article and confirm the current harmonised-standards list for your own file if the destination is the EU or Northern Ireland.
A brochure line that says “CE” or “EN 420” does not tell you the PPE category, the notified-body role if one is required, or whether the files belong to the exact model, size range, and material combination in your offer.
Protective gloves and medical gloves are different buying frames
This is the mix-up that causes the most wasted RFQs.
- Protective gloves are a wearer-protection / PPE conversation: general requirements (EN ISO 21420) plus the specific protection standard for the workplace risk, under the destination PPE rule—in the EU, Regulation (EU) 2016/425.
- Medical gloves are a patient/healthcare-barrier conversation: in Europe, the EN 455 series; in the United States, the FDA medical-glove pathway, including a 510(k) for Class I reserved devices.
A disposable nitrile glove can be offered in more than one of those frames, but the intended use, labeling, and files are not interchangeable. Do not copy a medical EN 455 pack onto a chemical-PPE offer, or a 21420/374 pack onto a medical examination claim.
Household and industrial latex protective gloves—including longer-cuff reusable styles—belong in the protective-glove frame unless the labeling actually makes a medical claim. See latex protective cuff length for a category-level length discussion, and keep that separate from disposable examination specifications such as ASTM D3578.
Naming 21420 or EN 420 on a brochure is not type-examination
- A general-requirements standard explains design, innocuousness, sizing, marking, and user information.
- A specific protection standard explains the risk the glove is supposed to address.
- A type-examination or declaration conversation is about the exact device or PPE model, the intended use, and the current files.
Marketing language that says “EN ISO 21420,” “ISO 21420,” or the older “EN 420” does not automatically mean the SKU in your cart has been assessed to the current text, marked correctly, or paired with the right specific standard.
Ask for an intended-risk statement, polymer and construction, size system, user information, the general-requirements evidence, the specific protection evidence, and destination regulatory files for the exact offer. Documentation should be confirmed by product and market. JUNDA’s /quality page discusses masked previews and file types; a certificate catalogue lists types of files available, not proof that every SKU carries every file.
Do not copy a sibling SKU’s paperwork onto a different length, lining, colour, or disposable/reusable construction.
RFQ checklist for EN ISO 21420-style conversations
- Destination market — EU, UK, or another named market, and whether PPE rules apply.
- Intended risk and job — chemical contact, mechanical work, wet cleaning, food handling, or another defined task.
- Regulatory frame — PPE, medical, food contact, or a combination that must be documented separately.
- Current general-requirements text — EN ISO 21420 (and the amendment the destination actually uses), not only a leftover “EN 420.”
- Specific protection standard(s) — for example EN ISO 374 for chemicals; name any other risk standard that belongs to the job.
- Product form — reusable protective, disposable PPE, arm protector, or another construction in scope.
- Materials — latex, nitrile, vinyl/PVC, leather, coated fabric, or a combination; this drives innocuousness questions.
- Size range and dexterity need — which sizes ship, and whether a dexterity level is actually being claimed.
- Marking and user information — what arrives with the goods, in which language.
- Destination documentation confirmed by product and market — see /quality; do not invent certificate numbers.
- Lot / batch evidence for the shipped lots, as agreed in the purchase terms.
Buying terms, lead time, and sample logistics are summarized on /buying. Prefer that page over repeating commercial numbers in every article.
FAQs
Q1. Is “EN 420 certified” still a complete buying requirement? No. SATRA states that EN ISO 21420 replaced EN 420:2003+A1:2009. Even when the current general-requirements text is named, ISO’s abstract says it does not address protective properties and is not used alone. Add the intended risk and the specific protection standard.
Q2. Does EN ISO 21420 mean the glove resists chemicals? No. Chemical protection is a separate selection. See chemical resistant gloves for EN ISO 374 language. A 21420 discussion covers general requirements such as innocuousness, fit, and user information.
Q3. Can I use EN ISO 21420 instead of EN 455 for medical examination gloves? No. SATRA frames EN ISO 21420 as a protective-glove general-requirements standard. Medical gloves follow a different pathway, such as EN 455 in Europe. See EN 455 medical gloves.
Q4. If a datasheet lists pH, chromium VI, or PAH limits, is that the same as a performance rating? No. Those innocuousness checks, as summarised by SATRA, are about substances and materials under foreseeable use. They are not a permeation, cut, or heat rating.
Q5. Does this article claim JUNDA protective gloves are EN ISO 21420 assessed or still EN 420 certified? No. Explicitly not. Guangzhou Junda Gloves Co., Ltd. (JUNDA) manufactures disposable programs under brands such as GYMDA and latex protective programs under series such as Yue Long and Baijiebang, and supports OEM/private-label discussion. Production bases include Guangzhou and Shaoguan (GYMDA Shaoguan disposable base). Whether a given SKU has PPE files, which standards are in scope, and how marking and user information read must be confirmed against the live product discussion and current documents—by product and market.
Q6. Where should buyers start on the JUNDA site? Start from long-cuff latex protective gloves, household flock-lined latex gloves, /oem, /quality, and /buying. Ask for evidence tied to the exact offer, not a generic “EN 420” or “ISO 21420” slogan.
Next steps for buyers
To discuss protective or disposable glove categories for your market, contact JUNDA by Email at sales@jundagloves.com or via the site WhatsApp button. Share destination market, intended risk and use, polymer and construction, size range, and documentation needs so the conversation stays tied to real labeling, user information, and current files—not to a brochure line that merely says “EN 420” or “ISO 21420.”
