If you buy disposable gloves for clinics, laboratories, or European healthcare export programs, you will almost certainly see EN 455 on a datasheet. Many RFQs simply write “EN 455 certified” and stop there. That slogan is too thin: EN 455 is a series. Different parts cover holes, physical strength, biological evaluation and labeling, shelf life, and—more recently—extractable chemical residues.
This guide explains those parts at buyer level, based on public testing-laboratory and regulator summaries: SATRA’s article on assessing single-use medical gloves to EN 455, the U.S. FDA Medical Gloves page, and a public NHS Wales SMTL restatement of examination versus surgical AQL figures. It does not claim that any JUNDA or GYMDA SKU is EN 455 assessed, and it is not medical advice. Confirm requirements against the current standard text, destination labeling, clinician or occupational-health guidance, and the files for the exact SKU and lot to be shipped.
What EN 455 is — and what it is not
SATRA describes EN 455 as assessing single-use medical gloves as a barrier—the risk of transmission between patient and healthcare worker. That is not the same as asking whether a glove protects the wearer from workplace chemicals.
What EN 455 is not:
- It is not a chemical-protection / PPE pathway. Wearer protection follows a separate route: the EU PPE Regulation (EU) 2016/425, plus EN ISO 21420 and EN ISO 374. If chemical contact is part of the job, see chemical resistant gloves.
- It is not the same as U.S. FDA medical-glove clearance. The two pathways should be asked for separately.
- It is not a substitute for naming intended use, polymer, powder-free finish, and destination documentation.
- It is not a certificate number you can invent from a blog. Documentation should be confirmed by product and market. JUNDA’s /quality page discusses masked previews and file types; a certificate catalogue lists types of files available, not proof that every SKU carries every file.
Surgical-glove remarks below are educational only. This article does not claim that JUNDA manufactures or supplies EN 455 surgical gloves.
Intended use comes first
Before any standard number is useful, say what the glove is for:
- A medical examination glove (and any other medical claim the destination market allows)
- A surgical glove for surgically invasive procedures—educational category only here
- A non-medical glove: general-purpose, industrial, or food-handling use, where medical-device rules may not apply
Polymer still matters. Nitrile, natural rubber latex, and thermoplastic films such as PVC or PE sit in different EN 455-2 strength categories and raise different allergy questions. For latex-protein policy, see latex-free gloves. For nitrile examination programs, see how to choose nitrile examination gloves.
SATRA’s public summary of EU MDR classification
SATRA restates how single-use medical gloves are typically discussed under the EU Medical Device Regulation (EU) 2017/745:
- Examination gloves are typically described as Class I (transient use, not invasive).
- Surgical gloves are typically described as Class IIa (surgically invasive) and, in SATRA’s summary, need Notified Body review of technical documentation and ongoing conformity.
Treat that only as SATRA’s public summary, not as a statement about any JUNDA product. Classification can depend on claims, sterility, and how the device is placed on the market. Confirm against current MDR text and the product’s own technical file.
The U.S. FDA pathway is separate
The FDA Medical Gloves page explains that U.S. medical gloves—patient examination gloves, surgeon’s gloves, and chemotherapy gloves—are FDA Class I reserved devices that require a 510(k). FDA reviews leak resistance, physical properties, and biocompatibility. Do not equate “discussed against EN 455” with “FDA cleared.”
The EN 455 series at a glance
Figures below come from SATRA’s public summary unless noted. They are not JUNDA factory data and not a specification for any SKU.
| Part | What it mainly addresses | Buyer question for the RFQ |
|---|---|---|
| EN 455-1 | Freedom from holes (water-tightness) | Examination or surgical positioning? Which AQL discussion applies? |
| EN 455-2 | Dimensions and force at break, including after ageing | Which strength category: surgical, non-thermoplastic examination, or thermoplastic examination? |
| EN 455-3 | Biological evaluation and related labeling | How are powder, latex protein, endotoxin (if claimed), and Type IV chemical residual risks labeled? |
| EN 455-4 | Shelf-life dating | Are dating claims supported by accelerated and real-time studies on packed product? |
| EN 455-5 | Extractable chemical residues (newer part) | If this part is in scope, what files exist for the exact SKU? |
EN 455-1: Freedom from holes
SATRA describes the water-tightness check as follows: the glove is fitted on a tube, filled with 1 litre of water, then inspected for leaks immediately and again after 2–3 minutes.
Sampling, in SATRA’s summary, follows ISO 2859-1 at general inspection level 1, code letter L. SATRA states that 200 gloves are tested under that scheme.
AQL figures commonly cited for this part:
- Examination gloves: AQL 1.5
- Surgical gloves: AQL 0.65 (SATRA notes that the surgical AQL was added in the 2020 version)
A public NHS Wales SMTL page restates the same pairing (1.5 vs 0.65). Treat both as public laboratory / technical summaries, then confirm against the current EN 455-1 text and the product’s own inspection records.
SATRA also illustrates that plan with a maximum of 7 failing gloves for the examination scheme and 3 failing gloves for the surgical scheme (under the 200-glove illustration). Use that only as a lab explainer of the sampling plan—not as a factory slogan and not as JUNDA quality-control data.
In U.S. conversations, buyers often see ASTM D5151. It is a widely cited hole-detection test method, not an AQL by itself. A method describes how leaks are looked for; an AQL describes how many defects a sampling plan will tolerate. Do not treat EN 455-1 and ASTM D5151 as automatically identical just because both involve water-leak checks.
EN 455-2: Physical properties
SATRA’s summary of EN 455-2 is more precise than a spreadsheet cell labeled “tensile”:
- Length and width use the median of 13 measurements.
- Force at break is checked on gloves as received and again after accelerated ageing at 70°C for one week.
- Three force-at-break categories are restated: (a) surgical gloves at least 9.0 N; (b) examination gloves except thermoplastic at least 6.0 N; (c) thermoplastic examination gloves (examples include PVC / PE) at least 3.6 N.
- If the finger wall is more than 10% thinner than the specimen area, a thickness correction is discussed.
These numbers are standard categories from a public laboratory summary, not published tensile results for any JUNDA product. Do not copy them onto a quotation as factory measurements. If force-at-break evidence matters, ask for the files that belong to the shipped SKU.
EN 455-3: Biological evaluation and labeling
Buyers often skip this part until a hospital or importer asks about powder, latex protein, or residual chemicals. SATRA’s summary includes:
- The manufacturer must provide details of harmful chemicals used, on request, and take precautions to reduce exposure.
- Powder-free labeling: if residual powder is below 2 mg per glove, measured via EN ISO 21171, the glove may be labeled powder-free. Powder-free and latex-free are different decisions; see powder-free gloves.
- If labeling claims “low endotoxin content,” endotoxins must not exceed 20 endotoxin units per pair.
- For natural rubber latex, extractable protein is monitored (SATRA cites the Modified Lowry method / Annex A). The smallest packaging unit must carry a latex warning and the latex symbol. The manufacturer must not claim “low allergenicity” or “low protein content.”
- Type IV residual-risk labeling applies to chemical ingredients such as accelerators, antioxidants, and biocides. That is separate from Type I latex-protein allergy, so a latex-free polymer (for example nitrile) is not automatically a “no chemical sensitivity” product. See latex-free gloves.
- Talc (magnesium silicate) is prohibited as glove powder.
Ask for labeling artwork and documents by product and market, and read them against the current EN 455-3 text.
EN 455-4 and EN 455-5: dating claims and extractable residues
A date on a dispenser box is a claim. EN 455-4, in SATRA’s summary, says the manufacturer must support it with both accelerated ageing and real-time studies; at least three lots should remain in their packaging; tests include freedom from holes and force at break, plus sterile pack integrity where sterility is claimed. SATRA states that shelf-life claims based on accelerated ageing are not to exceed three years. If later real-time results are inferior, the manufacturer must inform the authorities and change the claims.
EN 455-5 is a newer part. SATRA notes that it lists 27 chemicals, some of which are Type IV allergens, and that an amendment to EN 455-3 is expected to update related labeling. Mention this only at buyer level: this article does not invent that chemical list and does not claim that any JUNDA product has been tested to part 5. If extractable-residue evidence is in scope, ask what current files exist for the SKU.
How buyers should write an RFQ
- Intended use — examination, surgical (only if that is the real clinical use), or non-medical.
- Polymer — nitrile, latex, vinyl/PVC, or another named material; not “medical grade plastic.”
- Finish — powder-free if required.
- Which EN 455 parts are actually in scope for the destination market and claim set.
- Destination documentation, confirmed by product and market. See /quality; do not copy a sibling SKU’s paperwork onto a different product.
- Other pathways if needed — a 510(k) conversation for the United States; EN ISO 374 if the wearer needs chemical PPE; food-contact rules if the glove will touch food.
Related reading: powder-free gloves, latex-free gloves, chemical resistant gloves, and nitrile examination glove selection. Public summaries can lag behind the latest standard amendment; this article does not publish factory results or tell clinicians which glove to wear.
FAQs
Q1. Does “EN 455 certified” on a brochure mean the glove is ready for every European hospital tender? No. EN 455 is a series with different parts, and medical-device classification (as publicly summarized by SATRA under the MDR) also differs between typical examination and surgical claims. A brochure adjective does not replace intended-use language, the relevant parts, labeling, shelf-life support, and destination documentation for the exact SKU.
Q2. If a glove is discussed against EN 455, is it also FDA cleared? No. The FDA Medical Gloves page describes U.S. medical gloves as Class I reserved devices that require a 510(k). That is a different national pathway. Ask for each destination separately.
Q3. Why do examination and surgical discussions use different AQL figures? Public SATRA and NHS Wales SMTL summaries cite AQL 1.5 for examination gloves and AQL 0.65 for surgical gloves under EN 455-1 (SATRA notes that the surgical figure was added in the 2020 version). Those figures describe sampling expectations in the standard—not a quality slogan, and not JUNDA inspection data.
Q4. Does EN 455 tell me whether a glove will protect the wearer from chemicals? No. SATRA frames EN 455 as a medical-glove barrier standard. Wearer chemical protection is a separate PPE conversation (EU 2016/425, EN ISO 21420, EN ISO 374). Use a chemical-selection process when solvents, oils, acids, or prolonged contact are involved.
Q5. Can I treat SATRA’s “7 fails / 3 fails” illustration as a factory QC promise? No. SATRA uses that illustration to explain the ISO 2859-1 sampling plan (200 gloves; general inspection level 1, code letter L). It is a laboratory explainer, not a marketing claim and not a published JUNDA quality result.
Q6. How does JUNDA discuss EN 455-style documentation without over-claiming? At category level only. Guangzhou Junda Gloves Co., Ltd. (JUNDA) manufactures disposable programs under brands such as GYMDA and supports OEM/private-label discussion. Production bases include Guangzhou and Shaoguan (GYMDA Shaoguan disposable base). Whether a given SKU has medical-device files, which parts of a standard are in scope, and how labeling reads must be confirmed against the live product discussion and current documents. Start from disposable nitrile gloves, /oem, /quality, and /buying.
Next steps for buyers
When you write a tender, name four things separately: intended use (examination versus non-medical—and surgical only if that is the real clinical use), polymer, powder-free finish if required, and the destination documents you actually need. Then ask which EN 455 parts, if any, are being discussed for that exact SKU.
To discuss disposable glove categories for your market, contact JUNDA by Email at sales@jundagloves.com or via the site WhatsApp button. Share destination market, intended use, polymer preference, and documentation needs so the conversation stays tied to real labeling and current files, not to a generic standard slogan.
